Purchased to equip CT110 HUNTER CUBCT125 in winter.
When worn at the same time as Komine's Handlebar Cover, summer Gloves temperatures below 5 degrees Celsius are not a problem when MAXMODE is in use.
To plug in the retrofitted USB, I used DAYTONA CONNECTOBoots + Tie Band for rain protection. It seems to be no problem.
The only concern is that the grip heater will make the grip diameter thicker, making it a little harder to grip.
47.64 EUR (8,228 JPY)
Webike Point: +82 pt
(0.47 EUR)
información de entrega
Out of stock at the manufacturer.
Descripción del producto a continuación se traduce automáticamente por Google.
Product detail
[Especificaciones]
Conexión USB 5V2A
Con controlador
**Por favor, prepare un cargador con salida de 5V2.1A o más.
*Ten en cuenta que si lo utilizas con una salida USB de 1A, se calentará sólo la mitad.
*Es compatible con las empuñaduras normales (para empuñadura de 22mm: Φ30mm-Φ34mm de diámetro exterior), pero si te preocupa la holgura, por favor utiliza las bridas adjuntas para ayudarte.
*No es compatible con las empuñaduras americanas y otras empuñaduras gruesas (para mangos de pulgadas).
*La foto contiene otros productos.
*Tenga en cuenta que las especificaciones del producto pueden estar sujetas a cambios debido a la conveniencia del fabricante. Por favor, entiéndelo.
.
Modelos que se conectan al enchufe USB (Tipo-A) provisto en el vehículo.
El controlador del cable (diseño resistente al agua) permite encender y apagar el calefactor y ajustar la temperatura en 3 niveles.
[calentador de agarre de clip]
Fijación y retirada con un solo toque
La instalación es sólo una cuestión de "encajar y conectar la alimentación"..
Como es fácil de quitar, también es posible "quitarlo según la temporada, utilizarlo en varias motos"..
Corresponde a un agarre normal del mango (para el mango de 22 mm: Φ30 mm-Φ34 mm de diámetro exterior), pero si le preocupa la holgura, utilice las bridas adjuntas como ayuda..
No es compatible con las empuñaduras americanas y otras empuñaduras gruesas (para mangos de pulgadas). *Patentado*.
Uso eficiente de la energía.
Adoptando un material de calentamiento con alta eficiencia de conversión de calor y concentrando la superficie de calentamiento, lo hemos diseñado para aprovechar al máximo la potencia de 10W..
En comparación con el tipo de sustitución de la empuñadura, se puede reducir la pérdida de calor en el tubo de la empuñadura y la diferencia de temperatura debida a la diferencia de grosor entre el lado izquierdo y el derecho..
10W es el mismo nivel de consumo de energía que los intermitentes, y no hay que preocuparse por quedarse sin batería, algo habitual en los productos de calefacción..
Puede ser un poco insuficiente para los clientes que requieren la misma capacidad de calor que el tipo de reemplazo de agarre, pero es un producto con un excelente equilibrio de comodidad y funcionalidad..
Precaución
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Opiniones de los usuarios
Reviews with image
Jul 28, 2022
Helpful?
Jan 22, 2022
A winter necessity for mainly city driving.
I was looking for a removable Grip heater, but this Clip type product seemed to be easy to install, so I bought it.
I installed it on my PCX150KF30 and it works fine without the Tie Wrap.
The grip is thicker, which makes it unsuitable for sports driving, as it makes your palms feel tight for a long time.
The PCX doesn't require much accelerator operation, so it's just fine, but I'll remove it when it gets warmer.
It is not designed to heat up the entire grip, so it is used exclusively for fingertips, but I use the Handlebar Cover with it, so I think I can handle it even in the middle of winter.
I connected it to the ServiceCoupler- using a DAYTONA USB power supply, but it was warm enough.
Now I just have to see how long it will last.
I should have bought it sooner.
Helpful?
Dec 23, 2021
It is easy to install, simple but effective
I thought it would be good if I could use it only in the cold season, and I thought about the electric heating Gloves at first, but from the experience that I bought and used the electric heating Gloves several years ago, I couldn't do anything when the battery ran out, and the battery part was bulky, and the fit was not good. Then, I considered the wrapping type Grip, and I decided here that it was easy to put on and take off, could be powered from USB, and could adjust the temperature.
This product fits directly into your Motorcycle's Grip and plugs into the USBJack for easy installation.
There is a bit of resistance when fitting the product into the Grip, so it fits tightly, but if it gapes during use, you may want to use a Tie Wrap to secure it.
I installed it on my Yamaha SCR, but the grip on the Left side shifted outward, so I used a Tie Wrap to keep it from moving.
By inserting this product, the grip (22.2?) of NORMAL becomes thicker.
It seems that there are many people who feel uncomfortable that the Grip becomes thicker, but I do not feel uncomfortable because the feeling that I gripped is about to become the thickness of the Inch grip (25.4?) of the Cruiser system.
It's the heating effect that's important, but it can be adjusted by switching between three levels.
I use Three seasonGlove in the daytime (temperature 15~18℃) of October-November beginning Low." From "Inside about (when it is cold in the morning) "strength" ), daytime (about 15°C) in November. "Inside From "strength" In the daytime (around 10 degrees Celsius) in December, the winter Glove "strength" It is used in
As you can see, in December, it's not as good as a replaceable Grip heater.
It's more than warm. "Lukewarm." But even with this product, my fingertips don't get itchy.
The Heater part covers about half of the Grip's circumference, so you can decide where to put it (palm or fingertip) according to your preference. By the way, I choose the position so that my fingertips don't get bitten.
The difficulty is Waterproof of the USB power supply part.
Because it is bare, it is necessary to take measures to waterproof the feeding part when using it in the rain (I refrain from using it in the rain).
Helpful?
Dec 18, 2021
I guess it's better than nothing.
Even on the highest setting, the part where the Grip heater hits is slightly warm, but the rest of the body is not warm, so it's better than nothing.
I think that the electric heating Gloves that warm the whole hand are more effective!
Helpful?
Dec 8, 2021
This is my first Grip heater.
Because it is not a Type built into the Grip, it does not warm the entire palm of your hand, but it warms it enough. Of course, the back side of the hand is cold.
It is necessary to pay attention to the Grip because it becomes damaged when you put it on and take it off. At first, it wraps around the Grip tightly, and the position does not change even if Axel is twisted, but it comes to gap when using it.
Waterproof Specification, but I don't use it on rainy days because I don't want it to break.
Helpful?
New Custom Articles
