Anillo del cárter

I wouldn't want to repurchase if I could help it.

Fits:KAWASAKI Ninja 1000SX 24, KAWASAKI Ninja 1000 (Z1000SX) 17-20 ABS(ZX1000WHF)

Japanese Webike user

Very Good

Aug 22, 2021

I had purchased it thinking I would do it at some point, but the time finally came to use it.
I thought it would be easy, but the Double-sided tape was strong and quite Large strange to remove. It was easy to install once it was removed.

I wouldn't want to repurchase if I could help it.

Helpful?

I don't want to buy Repeat anymore (lol).

Fits:KAWASAKI Ninja 1000SX 24, KAWASAKI Ninja 1000 (Z1000SX) 17-20 ABS(ZX1000WHF)

Japanese Webike user

Very Good

Aug 1, 2021

In fact, after installation, I was embarrassed to say that it was a standing failure (and Quantity).:Pair (for Left and Right) I did (one at a time too) and this is the Review afterwards.
It wasn't a large impact because it was a standing mishap, but the Left Side Cover was well scratched, but the Crankcase was intact. I had OEM Slider and Slider was also scratched, but Cowl was not scratched.
He did his job well.
But even though it's a Cover, I didn't want to ride with the scratches, so I bought the same one and replaced it.
I thought that it was a little high that it cost more than 7000 yen with this, but I think that it will cost tens of thousands of yen when I change CrankcaseBody, so it is good.
It's made of plastic and it's only held together with double-sided tape, so I had my doubts about whether the crankcase would be protected in case of a violent fall while driving, but when I removed it, I felt that the double-sided tape was surprisingly strong and would not come off even if I pulled on it. I had to use Parts cleaner and SealRemover to get it off.
It's going to protect you until you fall over and the Plastic gets scraped off.

I don't want to buy Repeat anymore (lol).

Helpful?

I installed it to hide the scratches.

Fits:KAWASAKI Ninja 1000SX 24, KAWASAKI Ninja 1000 (Z1000SX) 17-20 ABS(ZX1000WHF)

Japanese Webike user

Very Good

May 4, 2021

I bought this to cover up the damage I did to my Crankcase last time I had a bad fall. It's made of plastic with double-sided tape, so I'm not sure if it will protect my crankcase if I take a nasty fall while riding, but I think it will lessen the impact more than not.
Plastic, but the texture is not bad.
To install, just degrease with parts cleaner and peel off the double-sided tape and fasten. I used a maintenance stand to set it up horizontally, but I think a side stand would have worked just as well, but I thought it would have been easier to set it up straighter since it's pretty low down.

Helpful?

Will it only end up being expensive?

Fits:KAWASAKI Ninja 1000SX 24, KAWASAKI Ninja 1000 (Z1000SX) 17-20 ABS(ZX1000WHF)

Japan User(translated)

Average

May 5, 2020

Material:It's plastic and double-sided tape, and when you touch it, it feels fluffy It is
It's expensive
I put it on in the OP when the car was new, but the reason was that the clerk recommended I put it on
Even with the Frame Slider on this motorcycle, if you take it down, you can get a Crankcase It's because it's going to get done There is no sense of being an afterthought
That's why I try to think of it as a deliberate attempt to make it cushiony and easy to replace I am
I haven't taken it down yet, so... how do I know if I've been tricked?

Helpful?

Fits:KAWASAKI Ninja 1000SX 24, KAWASAKI Ninja 1000 (Z1000SX) 17-20 ABS(ZX1000WHF)

Japan User(translated)

Poor

Dec 8, 2019

Plastic board

It was just a simple thing to attach a plastic board with double-sided tape other (esp. people)
Also, it is not a complete protection against the Crankcase in the event of a motorcycle collapse (after the -te form of a verb) not ..

And this price is too high for that