Protector del motor

【Texture】
The quality is fine.
It is a matter of Bolt strength rather than Slider strength.
If it falls over, it will probably bend.
[Usage.
Falling on one's feet・・・・◎ Minor injury
Public road・・・・・・◯ Good to know.
Circuit... Fat. Good to know.
Lawn, Gu Label・△ Extra resistance will occur.
In general, I don't think there are any negative effects from the installation.
(The above comment is an estimate.)
Installation procedure
Tools will be noted in the comments.
You can do it yourself, but do one side at a time.
The tightening Torque is 62 and there Torque.
Equipment of Guardetc.
DAYTONASlider (this product)
Engine Guard (y'sGEAROEMOption)
Rear stand hook (with separate imprint)
These are the three items above.
The bar end mirror is verified by removing it from the beginning because it is fatal to contact.
Results of the fall experiment
First, basic knowledge.
When the Motorcycle collapses, it is always in contact with the ground at some three points on the body. (Three points of ground contact stabilizes it.)
Tire (front wheel)
Tire (rear wheel)
Handlebar End
footpeg
SIDE STAND
Tandem Footpeg
Brake pedal、Shift Pedal
STAND
Crankcase (Engine GuardRight)
Generator cover (Engine GuardLeft)
Slider (this product)
etc., at least three of these points are always in contact with the ground.
The final stable ground is made at the Handlebar End, Slider, and Rear stand hook, but there are places where contact is made before reaching that point.
[For Left Side
Shift Pedal, Side Stand, and footpeg are almost simultaneous.
Tire floats quickly.
?Engine Guard
?Slider
Rear stand hook, Rear footpeg depending on angle
?Handlebar End
[On the Right Side
?Brake pedal and footpeg at about the same time.
Tire floats quickly.
?Engine Guard
?Slider
Rear stand hook, Rear footpeg depending on angle
?Handlebar End
【Review】
In either case, it will not hit the Tank unless something breaks or bends to Large width.
Also, there is an Engine Guard, so there is little chance of the vehicle becoming disabled.
Even if there is no engine guard, the crankcase and generator cover are unlikely to be damaged because the slider always enters at the three stabilization points. (The Crankcase and Generator cover will be scratched because they will make contact once before the three stabilization points including the Slider).
Assumption of inability to run
Handlebar breakage
footpeg fold
Fracture from the base of the Lever
Driver Injuries
【Cospa】
It doesn't have to be DAYTONA, but if you put it on, the cosmetics are enough to get you home even if you fall down.
I enjoy both Gymkhana and Circuit somewhat, so I thought about a sturdy Engine Guard (SSBetc.), but until my first fall, I thought I would try this Slider for appearance.
[Others]
For those who are concerned about the length of Slider.
If the Slider is too long, it will tip over to the Tank side (upper side of the Motorcycle) using it as a fulcrum.
It is a mistake to think that if it is long enough, no other contact will be made.

The image doesn't reflect, so it's up in the comment section of the ↓!

This is one of the parts that I always install when I buy a motorcycle!
That's it [Engine protector be (auxiliary used in place of "aru" after "de" or "ni" when forming a copula) [Frame Slider] The product is called

a staple for a stumbling block "I'm a good driver, I don't need these parts! If you're not sure what you're looking for, you can always ask your doctor. I don't necessarily beat myself? I'll give you a word.
I've had three Motorcycles in less than a decade, and each time I've beaten them for various reasons.
This is insanely embarrassing, but here's an example of why I fell! Here is an example.

? --Tumbling by the wonders of nature-- (Natural moss)
It was a windy day when the first day of spring blew………so strong that the motorcycle, which weighed 220kg, fell over while parked.
Thanks to the Frame Slider, the Engine was unharmed. (HALF COWL was crushed, but ……)

? --Surprised by the carcass of a cicada, he forgets to take out his Side Stand and falls over-- (standing goke with full of shame)
I arrived at the motorcycle storage area of the Large Home center, and just as I was about to take out the Side Stand, I saw the carcass of a cicada at my feet……!
I thought I was going to step on the carcass, so I paid Side Stand as soon as I could, but somehow I leaned my body to the Left and fell down. (I almost cried when the audience around me paid so much attention to me.

? --Self-imposed forward fall due to forward tilt -- (GEAR parked at N and self-destructed)
I headed to the ranch to eat SoftCream, but it was off-season and not open for business, so I parked my motorcycle in the back of the lot to take some pictures of my one-month-old motorcycle.
Because I didn't put in GEAR at this time, the Motorcycle, which is 270cm long, couldn't resist gravity and moved forward.
Succeeded in filming a video of a Motorcycle falling over by itself! (reopening)

……There are many other ways to moss, but it's a long story.
--What I was trying to say is that there are many reasons for falls.

Well, that's what they're for in case of an unexpected fall!

[Mounting]
Work with Ratchet wrench and Quantity Bolt:Pair (for Left and Right) In Quantity:It only takes 2pc removal, so it takes less than 5 minutes.
Even if you are a beginner in motorcycle tinkering, you can still do it, but you will need to have a torque wrench, service manual, etc.

Quality and Texture
It took a little over 3 months after installation to feel the effects (crying), so I didn't know if it would degrade over time or anything, but I had nothing to complain about in terms of quality or texture.

[Protective nature]
As shown in the Product Page, the effect is not sufficient in this product Single Body.
You should always follow this warning!
? YamahaOEMAttachment (Side Slider:Manufacturer part number Q5KYSK081E03) It is recommended to use with ?
If you think normally, Engine and Slider will be rubbing against the ground if you support by one point, you can reduce the damage to Engine as much as possible by installing another Slider.

Conclusion
The effect is preeminent when it uses it with OEMSlider though I made it -1☆ because it doesn't make much sense with Single Body.
I don't think anyone falls over because they want to, but I would like to recommend the introduction of a fall prevention system!
This is a must have Level, especially for motorcycle beginners! It is recommended to install this product first in case of emergency.

I had it installed at the shop when I bought my new car LargeI was happy with it, but it cracked after 2 years of installation I never once hit it by standing or falling There may be a difference in the quality of the individual pieces, but I think it's a bit of a shame

【What made you decide the purchase?】
Purchased for the purpose of alleviating the damage of the vehicle caused by fall by using Circuit traveling.
【How was it actually used?】
The other day I raised SlipDown at the time of Left turning of HSR Kyushu Racing course and toppled over.
Used with other company's products (OEMOPEngine slider ? babyfaceRear Sets ? RDmotoRear Axle Slider), but Engine and Frame ? I think the exterior has been unharmed, so I guaranteed it securely.
* Car Both Sides's Damage is a Clutch lever (Foldable) The extent to which Bar End rubbed. It may break unless Retractable Lever is introduced.
【Mounting was difficult?】
It is not difficult because you can stop at Bolt 1 pc each.
【Please tell me the installation point and hang】
In order to remove Engine mounting Bolt, I think that those who worked One Side at a time will be less likely to hurt Screw Mountain.
[Is there anything I was disappointed about?]
None.
【Hope for Manufacturer ? Please let me know if there are any improvement points]
There is also this.
【Have you compared items?】
price ? Delivery date ? I did not have this as it was a nomination buy when I saw Brand.
[Others]
As Repair Parts for falling, it is very appreciated that there is only One Side setting.
Also as stated in the description of the product, not only for XSR 900 but for the MT-09 type car structure, Left SideCrankcase is out of the vehicle, so it can not be protected with this product alone.
Be sure to use Engine Guardetc. Please use in conjunction.

they look really good, blends right into the bike. very easy in install just need to make sure you have sorted out the bolts right. one of them is longer then the other and one of the washers is thicker. like it said in the description the directions it comes with are in Japanese so unless you have a friends who can read it out to you its pretty much just a guessing game.