Kit RAPiD BIKE-EASY

【vehicle inspection】
I attempted to go through the inspection on the vehicle inspection, I passed without problems. Motorcycle passed, 11 years exhaust Gas (Legal regulations are loose) , Catalyst of Other Brand Product (Good performance of catalyst) Because of the condition that it is unknown whether other Motorcycle will pass as well. However, as the sales agent of this part has appealed to Japanese Vehicle Inspection Correspondence, why do not people of the User Assessment School try it?

【Installation】
Because of CouplerON, installation is very easy. Because our Motorcycle parts are equipped with Grounding Wire, we dropped it from Tired Lamp's Grounding Wire. Where to place Body is a point that suffers from Motorcycle individually. It is a waterproof compliant product, but I think you should avoid places that are subject to water.

【parts】
It is the part that adjusts Volume without contact and issues Setting. By doing this adjustment finely, you can set your preference. I am fine-tuning Memory further to fine-tune like the photo. Also, adjustment dial and operation confirmation LED can not be adjusted when the lid is closed ? What I can not see is MinusPoint. Furthermore, it is troublesome to remove the lid with a Screw clasp. We adjusted by attaching Small window ? Improve it so that it can be checked.

【Review】
Recent bike (My bike has fallen by 10 years ? ? ? ), Exhaust gas response ? With improved fuel economy, the low fuel economy in the low revolution range is weak and the torque shortage can not be denied. It is a good part to improve here. However, ? If you want to improve the high rev range, this part is inadequate. Since this part makes the fuel concentration rich over the whole area, when setting is done with low rotation, ? Dissatisfies with the feeling that the high rotation is too dark. Although it can not be said that all the motorcycles will be like this, it is better to think that it is a part that improves the feeling of gyroschek in the low revolution range, I would recommend it to those who want to improve here. If you want more than this, I'd recommend wearing more solid, subcontact, full control.

Purchase by just the information written in the image and the netShopping gap Punctured image resolution I felt like a way of selling Resolution fraudulent smell
It might be my own thought, but the texture of Aluminum wind body of Silver lame was disappointing
Moreover, things with items that can not be returned

Shiver 750 is a low-speed skusca, but it has improved considerably with this.
NORMAL was used only for high revs but Power came to come out from the middle.

When I was thinking about Exhaust System exchange, I heard that it is better to adjust the fuel injection. Telmi with ECU is out of stock! じ ゃ ~ Outside Slip-on Silencer ___ ___ 0 But, I knew this product when I thought it was expensive and troublesome.

Since the goods arrived during the ordering period of the Exhaust System, we installed them as OEMExhaust System.

I did the installation myself. Coupler position to be interrupted was in the vicinity of FuseBOX through the front bank behind the exhaust Device and the rear bank through the vicinity of the exhaust Device → V bank. Body seemed to be under Tandem seat, but since it has ETC, it is set under Seat.

Test drive immediately with recommended setting! Oh! If you think TorqueUP is stopped Engine with signal! Cause the Wiring touched Exhaust System and Fuse was flying - - -. Please pay attention to the arrangement near the Exhaust System - - -.

The effect became sticky at low speed, the time to make half a crane became less by entering an intersection etc.. Also, it turned to Smooth until the high rotation side, the vibration decreased. I felt that the Engine which had been killed because of the automobile inspection adaptation in the OEM fuel-supply returned to its original performance.

Sub computer installation and ECU exchange are high at 848! Mendozai! But if you want to make it easy to get on you can recommend it!

Once you install it, you will soon see the difference. You refer to Impression of other people there.
The most problematic thing in purchasing this product is whether it is fitting my own model and I think that it is a mounting method. Since the manufacturer is asking for installation with a proper shop, keep it in mind.. Whether or not it fits can be determined by the fact that there is an O2 sensor in the exhaust pipe with an injection car. It will be it if the part with the electrical cable is screwed in following the exhaust pipe. After that you will follow that cable and you can install it if you look for a coupler. I attached it to the MotoGucci V7 Classic 2012 year ceremony. Since iOS can not update the photos here, "diary" And I updated the details on the external blog. I installed it at a motorcycle shop, but as for the installation method I was saved because the agency gave me information as long as it was through WEBIC.