* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I bought it for using Side bag with SEROW 225we. Although it is a simple Side bag support, the effect as a Side bag support is Small but it is absolutely Large, there is a difference between Large and None. Since the movable range of the Joint part is wide, it is easy to adjust the mounting position. The Exhaust System side can install it by avoiding the Up type Exhaust System that tends to be off if you offset it to the outside and install it. As a precaution, since the Joint part is fixed only by tightening the Screw, it will loosen unless it is tightened regularly. If you have many opportunities to travel on bad roads, we recommend using Screw lock together.
It is possible to install it besides CT110 HUNTER CUB, and the mediocrity is high, but the product which is similar well is less than half price in A●ZON in CHINA, and when it also buys it and it compares it, there is no Large difference except the making of the detail.View Detail
I wanted to attach a side bag to my Monkey 125, and as a result of looking for various things, I ended up with this product. Because the body of the car is small, it is not possible to put on a bag that is too large, so I pulled out the cheap genuine leather bag that I had used before, and when I tried to match it, it was a good feeling… so I started to work, but the installation place is the upper bolt of the rear suspension, and I decided to use the tightening strategy. WasherQuantity on the outside of the rear suspension:The bag's belt is attached to the frame on the front side and to the carrier on the back side, and the bottom of the bag is secured to the bracket with a Tie Wrap to prevent it from flapping and to prevent it from falling off. The bottom of the bag is secured to the bracket with a Tie Wrap to prevent it from flapping and falling off. The bag is very simple to install and can be used in a variety of positions. The installation method is up to your Ideas!View Detail
Rough & Road Back with other Manufacturer's Side BackGuard When I tried to install it, it seemed to hit the Tire, so I bought this product. I didn't think about it from the beginning, but other companies' products were specially designed for Z900RS, so I decided to install this one. I installed it because I couldn't get it to work. It fits in well.View Detail
I haven't installed it yet, but it's more solid than I expected and seems to be easy to install. It seems to be able to support the Side Back sufficiently. I think I will install it as soon as possible this weekend.View Detail
I can't complain too much about the price, but I feel that it cannot be fixed tightly I've tightened it up quite a bit, but it moves pretty easily when you move it by hand I'm not sure if this is the case or not The important point is that the Joint part was rusted from the beginning I've never seen this happen before Normally this would be an Objection Level case, but it's too much trouble, so I'm using it as is (T-T) I installed the Side Back and my impressions are very good (By the way, school bag) The motorcycle is a Bell RC50View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING