18.09 EUR
(2,949 JPY)
17.23~ EUR
(2,809 JPY)
(5% OFF)
4 (13 opiniones)
Average
It's neither good nor bad[How is it used?
Introduced along with the change of Separate handle of XJR1300C in the town riding and Touring Main.
Was the one you received as per Image?
I had it in my old MainMotorcycle and it is as Image.
Was the installation difficult?
As long as the inside diameter is correct, there is nothing particularly difficult to do.
However, although the Handlebar I.D. supports up to 17φ, when tightened with 17φ, the
You should put Washer in there because Nut, the turning stopper, will come over Rubber.
How was your experience with it?
The vibration of the Handlebar has been reduced. But of course, the Handlebar itself is obviously heavier.
[Included Parts:were they on?
It is as shown in the product image.
[Was there anything that disappointed you?
If you tighten it up, the Nut will be buried in the Rubber and the Torque will be gone.
Reviews For ACTIVE peso interno From Other Webike User
Very Good
Not reduced to zero, but there is a mitigating effect.[How is it used?
When the Ninja 400 was replaced with Other Brand ProductHandlebar, the OEM heavy bar end could no longer be installed.
Was the installation difficult?
It can be attached using only a hexagon, but since it is long enough, be sure that the length is compatible with the handlebar in advance.
In addition, if a Bar End is to be installed, it should also be taken into consideration.
How was your experience with it?
The vibration never went away, but it was much better.
It is worth a try because the effect is so different that it can be felt.
[Included Parts:were they on?
Everything was included.
[Was there anything that disappointed you?
None in particular. Seems a bit expensive, but affordable compared to Bar end weight.
[Notes]
The OEMHandlebar of the Ninja400 is not supported.View Detail
Average
Does it work?I was curious about the vibration of the FZ1 FAZER, so I popped it in. I've been using it for a while now, but I'm not sure if it's worth it. I'm going to use it for a while.View Detail
Poor
Hmm, subtle?When I replaced the Handlebar, I was concerned about vibration, so I did some research and purchased this product.
Initially, I felt the slight vibration more than before I put it on. I think this is counterproductive. I thought it was a good idea, but lately I don't mind it anymore.
I don't know if it's because I'm used to it or if it's because of the effect of the Parts.
I've been wearing it for a while now.View Detail
Very Good
It will be reduced to some extent, but not to Zero.[How is it used?
Installed when replacing with SNIPER's Handlebar.
Was the installation difficult?
A Hexagonal Wrench is easy to install, but a Bolt is required for removal.
How was your experience with it?
I introduced it because I had replaced the bar end weight with a lighter one and the vibration increased.
The vibration that made my hands numb and itchy has been reduced to a level that doesn't tire me that much even after a long run. I can't say that the vibration was reduced to zero, but I could feel the effect of the reduction.
If you want to replace the bar end weight with something you like the look of, but it is too light, you should consider this product.
[Notes]
It is not compatible with the OEM Handlebar of the Ninja 400.View Detail
Poor
I introduced it as a numbing agent, but...I installed it to prevent numbness in my hands due to vibration, but unfortunately it had little effect on my Motorcycle.
"Better than nothing." It was a degree.
I guess the effect varies by car model and Handlebar.
By the way, the Bar End diameter of rizoma is 17mm, but I chose 13-17mm compatible because the back is narrower.View Detail
Most Viewed Reviews Of ACTIVE Bar End Weight
Very Good
Not reduced to zero, but there is a mitigating effect.[How is it used?
When the Ninja 400 was replaced with Other Brand ProductHandlebar, the OEM heavy bar end could no longer be installed.
Was the installation difficult?
It can be attached using only a hexagon, but since it is long enough, be sure that the length is compatible with the handlebar in advance.
In addition, if a Bar End is to be installed, it should also be taken into consideration.
How was your experience with it?
The vibration never went away, but it was much better.
It is worth a try because the effect is so different that it can be felt.
[Included Parts:were they on?
Everything was included.
[Was there anything that disappointed you?
None in particular. Seems a bit expensive, but affordable compared to Bar end weight.
[Notes]
The OEMHandlebar of the Ninja400 is not supported.View Detail
Average
Does it work?I was curious about the vibration of the FZ1 FAZER, so I popped it in. I've been using it for a while now, but I'm not sure if it's worth it. I'm going to use it for a while.View Detail
Poor
Hmm, subtle?When I replaced the Handlebar, I was concerned about vibration, so I did some research and purchased this product.
Initially, I felt the slight vibration more than before I put it on. I think this is counterproductive. I thought it was a good idea, but lately I don't mind it anymore.
I don't know if it's because I'm used to it or if it's because of the effect of the Parts.
I've been wearing it for a while now.View Detail
Very Good
It will be reduced to some extent, but not to Zero.[How is it used?
Installed when replacing with SNIPER's Handlebar.
Was the installation difficult?
A Hexagonal Wrench is easy to install, but a Bolt is required for removal.
How was your experience with it?
I introduced it because I had replaced the bar end weight with a lighter one and the vibration increased.
The vibration that made my hands numb and itchy has been reduced to a level that doesn't tire me that much even after a long run. I can't say that the vibration was reduced to zero, but I could feel the effect of the reduction.
If you want to replace the bar end weight with something you like the look of, but it is too light, you should consider this product.
[Notes]
It is not compatible with the OEM Handlebar of the Ninja 400.View Detail
Poor
I introduced it as a numbing agent, but...I installed it to prevent numbness in my hands due to vibration, but unfortunately it had little effect on my Motorcycle.
"Better than nothing." It was a degree.
I guess the effect varies by car model and Handlebar.
By the way, the Bar End diameter of rizoma is 17mm, but I chose 13-17mm compatible because the back is narrower.View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING