* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Hello you all! Just recieved my minimoto mounting rubbers and bushings. First of all the quality is good for the money they cost. Though i dont know how they will last in the long run. Hope the rubber doesn't harden with time. They mount up very good. The rubber feels like it is high quality. I like that you get the whole setup for the cheap price they cost. It certaintly meet up with my demands.
Product was packaged well. Fast postage. Rubber seemed ok, nice and soft. Problem was tank rubbers. The inside tank mounting hole measured 10mm. My Z50J1 1976 frame measured 5mm, so these rubbers were too big for my frame. I have now had to order 2 new tank mounting rubbers obtaining the correct Honda part.View Detail
I used it to install a Gorilla tank on my MONKEY. Back side of Tank (Bolt tightening point) The OEM was one piece, but this is a split type, but no problem at all. If I had to venture a guess, I would say that if you carry a tank with a split bush attached, the bush may come off. There is some BALI, but not enough to be bothersome. The OEM was quite soggy and may be replaced if there is an opportunity to remove the Tank.View Detail
I used this one on a 6V early GORILLA. This is helpful because some OEM Parts have already been discontinued. Quality is also OEM and no loss. It's cosy.View Detail
its just the support plate, not the bracket like shown in ALL of them pictures, a bit misleading since there isnt any picture of just the plate.though it looks good qality its not what I need.View Detail
Really wanted to attach the old CT sub tank to my new trail and this was the best solution I had found at the time. In practice is really flops around alot on the dirt trails and I have seen too many posts of it snapping off the mount on the bike due to the weight of the sup tank. Needs to mount to more than one location. It will work totally fine if you never take the bike off road.View Detail
Product was packaged well. Fast postage. Rubber seemed ok, nice and soft. Problem was tank rubbers. The inside tank mounting hole measured 10mm. My Z50J1 1976 frame measured 5mm, so these rubbers were too big for my frame. I have now had to order 2 new tank mounting rubbers obtaining the correct Honda part.View Detail
I used it to install a Gorilla tank on my MONKEY. Back side of Tank (Bolt tightening point) The OEM was one piece, but this is a split type, but no problem at all. If I had to venture a guess, I would say that if you carry a tank with a split bush attached, the bush may come off. There is some BALI, but not enough to be bothersome. The OEM was quite soggy and may be replaced if there is an opportunity to remove the Tank.View Detail
Hello you all! Just recieved my off-set front sprocket for my Z50. It works like a charm as i have the kepspeed wide swingarm. The quality feels nice and it mounts up perfectly with my 12 inch wheels that i got from a Honda grom. Just wished that they got bigger sizes than 17. Maybe they will manufacture bigger in the end. I will give the sprocket a big thumbs up for the price and the quality!View Detail
Hello you all! Just recieved my g-craft nsr mini forks. They mount up nicely with my Agras triple tree's. The quality seems good and i like that you can adjust the dampening on them. The dampening isn't to soft or to stiff when i got them. But that depends on what you use them on. I use them on a Z50 with 12 inch wheels and they work great. Much better then my chinese forks that i had before. View Detail
Hi you all, This product is of the highest quality and finish, its fits and works great. I would highly recommend this product to anyone who is in need of a good setup. Very Nice fitment with using honda nice forks. Good information about the item and shipment. Very fast production time even though it states a month it only took me two weeks. i highely recommend this item.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING