país de origen : China
fabricante : KEPSPEED
*Es difícil instalar la cubierta del generador para el mono FI (vehículos de inyección de combustible) porque la forma de la cubierta del generador es diferente. Se requieren muchas modificaciones.
[Instalación]
*La rueda dentada de tracción se mueve hacia fuera de manera significativa, por lo que es necesario raspar una parte de la cubierta del generador del motor en el que se instala este producto.
*Es difícil instalar la cubierta del generador para el mono FI (vehículos de inyección de combustible) porque la forma de la cubierta del generador es diferente. Se requieren muchas modificaciones.
*Los valores estándar de desplazamiento son 26,5 m y 18,5 mm. Para otros valores de desplazamiento hay que modificar el espaciador del eje.
*KEPSPEED no ofrece el mecanizado para ajustar decalajes distintos a los valores de decalaje estándar.
*Algunos motores chinos están diseñados para tener sólo 3 placas protectoras, excepto la parte inferior trasera. En tal caso, puede usar el motor con tres posiciones de placa protectora, pero por favor no modifique la placa protectora.
*Las instrucciones de montaje (para el kit completo) están incluidas en el paquete. Por favor, consulte el manual y ensamble el equipo cuidadosamente. Sin embargo, el manual no incluye las instrucciones de mantenimiento.
*Necesitará a alguien con experiencia en mantenimiento de motocicletas para hacer el trabajo de montaje.
*Incluso si la suspensión trasera está al fondo, asegúrate de que no haya anormalidades en los puntos de contacto.
*Se da el caso de que hay un ligero cambio de especificación en la parte detallada de cada producto. Hay un punto que difiere ligeramente de la imagen de introducción, pero voy a dar prioridad a lo actual, así que por favor, comprendedlo, por favor.
*Buscamos un técnico de mantenimiento de motocicletas para hacer el montaje en un taller especializado en mantenimiento de motocicletas.
*Después de que empiece a funcionar el motor, tenga en cuenta la holgura inicial de los muelles e inspeccione los muelles con frecuencia para evitar problemas inesperados.
[Sobre la garantía del fabricante]
*Pueden producirse pequeños arañazos y abrasiones debido a problemas de transporte.
*La garantía del fabricante no es aplicable, excepto en el caso de defectos que perjudiquen significativamente el valor o la función del producto.
*No aceptamos devoluciones por ningún motivo.
*En muchos casos, el desajuste entre el estado del coche y las condiciones de conducción o el estado del vehículo es la causa del problema después de empezar a conducir.
*Se utilizan cojinetes con el número de pieza 6001ZZ (sellados por ambos lados), pero no hay piezas de repuesto disponibles.
*Tenga en cuenta que las especificaciones del producto pueden estar sujetas a cambios debido a la conveniencia del fabricante. Por favor, entiéndelo.
*Debido a que este producto se fabrica en el extranjero, el moldeado, la soldadura, la pintura, etc. pueden ser incompletos. Puede haber algunos arañazos y rozaduras menores debido a problemas de transporte.
Country of origin :China
Manufacturer: KEPSPEED
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*It is difficult to install it on the fuel injection vehicle (FI) MONKEY because the shape of the generator cover is different.A lot of work is required.
[About the installation]
*Because the drive sprocket of this product moves outward greatly, it is necessary to cut off a part of the generator cover of the engine to be installed.
*It is difficult to install it on the fuel injection vehicle (FI) MONKEY because the shape of the generator cover is different.A lot of work is required.
*The standard offset values are 26.5m and 18.5mm.To set other offset values, the shaft spacer must be modified.
*KEPSPEED does not offer any machining to set an offset other than the standard offset value.
*On some engines made in China, the protector can only be fixed in three places except for the lower rear part.In such a case, the protector plate can be fixed in three places, but please do not modify the protector plate.
※Instructions for assembly (for complete kits) are included.Please refer to the instruction manual and assemble carefully.However, common sense techniques for maintenance work are not described in the manual.
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
*Please have assembly work done in a specialist shop regarding motorcycle maintenance.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
※Some minor scratches and scuffs may occur due to transportation issues.
※GM-MOTO does not accept returns for any reason after the product has been installed.
*In addition, problems after the start of riding are often caused by riding conditions, maintenance conditions, or a mismatch with the condition of the vehicle, and are difficult to distinguish from the causes of individual products. Therefore, all will be disclaimed.
*The bearing is part number 6001ZZ (sealed on both sides), but there are no replacement parts available.
*There may be changes in product specifications due to the manufacturer's reasons.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.