Sensor digital 3G de alto rendimiento!
Este kit es fácil de usar, incluso para los principiantes..
El control remoto no es necesario.. ¡Puede desactivar el ajuste fácilmente con sólo encender y apagar la llave de encendido!
El sensor digital 3G suena una alarma de 122db cuando la actitud del vehículo cambia más de 5 grados..
Las características de este kit para los modelos de coches es que viene con instrucciones sobre cómo cablear y dónde instalar el sensor, la sirena y los LEDs indicadores..
La longitud del sensor se ajusta según el tipo de coche, así que los cables largos no interfieren con la instalación..
Es fácil poner la alarma en la posición de aparcamiento lateral o central..
[Método de montaje]
Quita el asiento y la cubierta del lado izquierdo..
Conecte el sensor CS-550M al soporte que sostiene la batería y conecte el cable rojo al lado positivo del sensor y el cable negro al lado negativo de la batería.. El sensor se fija con cinta de doble cara, pero puede evitar que el sensor funcione mal si lo fija con un cable..
Hay una cubierta de goma roja en el lado positivo, por lo que si pasas el cordón rojo a través de ella como se muestra en la foto, puedes cubrir la cubierta de goma muy bien..
El altavoz está conectado al lado exterior de la caja de la batería en la cubierta del lado izquierdo y conectado al sensor..
Retire la tapa trasera del guardabarros.. El círculo amarillo tiene dos tornillos, el círculo rojo tiene dos remaches de empuje. Quítenlos todos y la tapa se quitará..
Hay un acoplador impermeable de 3 piezas para la luz trasera en la cubierta de goma translúcida rodeada en rojo en la imagen.. El cableado es un acoplador impermeable con cables negros, verdes y verdes/amarillos, para que puedas reconocerlo fácilmente..
Conecte el cable naranja del sensor al cable negro de la luz trasera con un electrochoque..
La luz indicadora está fijada al marco entre el tanque y el puente superior.. Conecta el cable al sensor y vuelve a juntar el asiento y la cubierta del lado izquierdo para terminar el trabajo..
Se tarda unos 30-40 minutos en llegar aquí.. La posición de instalación de los sensores y la sirena se muestra en el manual y es muy fácil de seguir..
[Operación]
1) Pare el motor apagando la llave..
2) Encienda la llave y luego apáguela inmediatamente..
3) Se oye un breve pitido, la luz roja del indicador brilla durante 0,5 segundos, luego se apaga durante 2 segundos y luego se repite..
4) La alarma está ahora activada..
Durante aproximadamente un minuto después de que se active la alarma, no suena ninguna sirena aunque detecte una anomalía, pero la luz indicadora parpadea rápidamente..
Cuando detecta una anomalía después de 1 minuto, la luz indicadora parpadea rápidamente y la sirena hace sonar una alarma fuerte de 122db..
■High performance digital 3G sensor!
・This is a special kit for a long-selling burglar alarm that is easy to use even for beginners.
・No remote control required.The setting can be easily canceled only by operating the ignition key ON / OFF!
・The digital 3G sensor sounds a 122dB alarm when the vehicle's attitude changes by more than 5 degrees.
・The feature of the kit is that it comes with instructions on where to install the sensor, siren, and indicator LED, as well as instructions on how to connect the wires, so you can easily install it without worrying about the placement of each part, unlike universal kits.
・The wiring of the sensor itself has been adjusted to the appropriate length for the model of vehicle, so it can be installed neatly without unnecessary long wiring getting in the way.
・The alarm can be easily set on either the side stand or center stand.
[installation instructions]
・Remove the seat and the left side cover.
・Attach CS-550M sensor unit on the bracket holding the battery, and connect the red cord of the sensor unit to the positive side of the battery and the black cord to the negative side.The sensor body is attached with double-sided tape, but it is recommended to fix it with a bundle band to prevent malfunction.
・There is a red rubber cover on the plus side, so if you put the red cord through as shown in the image, you can cover the rubber cover nicely.
・The speaker is attached to the outer side of the battery case in the left side cover and connected to the sensor itself.
・Remove the cover from behind the rear fender.The yellow circles have two screw locations, and the red circles have two push rivets.Remove them all and the cover will come off.
・The waterproof 3P coupler of the taillight is located in the translucent rubber cover circled in red in the image.The wiring is a waterproof coupler with three wires (black, green, and green / yellow), so it should be easy to find.
・Connect the orange cord of the sensor to the black cord of the taillight with an electro tap.
・Attach the indicator light to the frame between the tank and the top bridge.Connect the cord of the sensor body, and put the seat and the left side cover back together to complete the work.
・It takes about 30-40 minutes to get here.The installation position of the sensor and siren is shown in the instruction manual, so it is very easy.
[operating instructions]
1) Stop the engine with the key OFF.
2) Turn the key ON and immediately turn it OFF.
3) A short beeping sound is heard, and the red indicator light shines for 0.5 seconds, then goes out for 2 seconds, and the operation is repeated.
4) The alarm is set.
The siren will not sound for about one minute after the alarm is set, even if it detects an abnormality, but the indicator lamp will flash at high speed.
When an abnormality is detected after one minute, the indicator lamp flashes rapidly and the siren emits a loud alarm sound of 122db.