Valor de compensación : 48.5m, 18.5mm (2 lugares)
hecho en China
*Este producto es un producto de KEPSPEED, un fabricante de piezas de aluminio de alta calidad.
*Es difícil instalar la cubierta del generador para el mono FI (vehículos de inyección de combustible) porque la forma de la cubierta del generador es diferente. Se requieren muchas modificaciones.
*La rueda dentada de tracción se mueve hacia fuera de manera significativa, por lo que es necesario raspar una parte de la cubierta del generador del motor en el que se instala este producto.
*Los valores de desplazamiento estándar son 48,5 m y 18,5 mm (en el lado del motor de la rueda dentada). Si quieres establecer otros valores de compensación, necesitas modificar los espaciadores del eje.
*No ofrecemos servicios de procesamiento para la creación de un offset que no sea el valor de offset estándar.
*Algunos motores chinos están diseñados para tener sólo 3 placas protectoras, excepto la parte inferior trasera. En tal caso, puede usar el motor con tres posiciones de placa protectora, pero por favor no modifique la placa protectora.
*Las instrucciones de montaje (para el kit completo) están incluidas en el paquete. Por favor, consulte el manual y ensamble el equipo cuidadosamente. Sin embargo, el manual no incluye las instrucciones de mantenimiento.
*Necesitará a alguien con experiencia en mantenimiento de motocicletas para hacer el trabajo de montaje.
*Incluso si la suspensión trasera está al fondo, asegúrate de que no haya anormalidades en los puntos de contacto.
*Después de empezar a usar el motor, tenga en cuenta la posibilidad de un aflojamiento inicial.
*Pueden producirse pequeños arañazos o abrasiones debido a problemas de transporte. No garantizamos los productos excepto por defectos que perjudicarían seriamente su valor y función.
Offset value: 48.5m, 18.5mm (2 locations)
made in China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*This product is a product of KEPSPEED, a manufacturer of high quality aluminum parts.
*It is difficult to install it on the fuel injection vehicle (FI) MONKEY because the shape of the generator cover is different.A lot of work is required.
*Because the drive sprocket of this product moves outward greatly, it is necessary to cut off a part of the generator cover of the engine to be installed.
※The standard offset values are 48.5m and 18.5mm.(To set other offset values, it is necessary to modify the shaft spacer.
※GM-MOTO does not offer any processing to set an offset other than the standard offset value.
*On some engines made in China, the protector can only be fixed in three places except for the lower rear part.In such a case, the protector plate can be fixed in three places, but please do not modify the protector plate.
※Instructions for assembly (for complete kits) are included.Please refer to the instruction manual and assemble carefully.However, common sense techniques for maintenance work are not described in the manual.
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
*There may be changes in product specifications due to the manufacturer's reasons.