Un juego completo que incluye el pedestal y los tornillos necesarios para la instalación.
¡También se incluye en el juego una edición limitada del forro interior de la caja trasera!.
Nuevo portaequipajes trasero para los cuatro modelos..
La Yamaha YZF-R25 y YZF-R3, MT-25 y MT-03 comparten el mismo motor y bastidor.. Hemos desarrollado un soporte trasero que se puede montar en cuatro modelos diferentes ajustando la configuración del vehículo..
La YZF-R25, con su carenado y diseño inspirado en el deporte, y el MT-25, con su imagen de luchador callejero. Ambas motos tienen una imagen delgada y nítida, un peso ligero y un rendimiento potente..
El portador trasero es una parte práctica, pero lo hemos diseñado para que sea lo más nítido posible sin destruir su imagen..
Diseñado para ser lo más afilado posible mientras se mantiene el espacio para el pasajero.
Inicialmente, puse el marco del portador trasero hasta el borde del asiento para no destruir la imagen nítida y ajustada.. El diseño es exactamente lo que quería, pero cuando intenté sentar al pasajero, se quedó corto..
Por lo tanto, lo diseñamos un poco más ancho que la muestra inicial para que haya más espacio para que un hombre grande se siente en el asiento del pasajero.. Más ajustado sin sacrificar la comodidad del pasajero.
La capacidad máxima de carga es de 5 kg.. Lo estamos reforzando en muchos lugares..
Hoy en día, es cada vez más común instalar un estante trasero y una caja trasera como un conjunto, incluso en vehículos que están diseñados para parecerse a los superdeportivos.. Como algunas de las cajas traseras más grandes pesan unos 5 kg, hemos reforzado todas las partes para mantener la capacidad de carga máxima hasta 5 kg..
Hemos puesto placas de refuerzo en el marco donde se monta el bastidor trasero, y también hemos puesto refuerzos en las piernas del cuerpo..
La forma de las nalgas está diseñada con la practicidad y el diseño en mente.
Cuando se instala la caja trasera, si la tapa se abre en horizontal o en vertical, la tapa puede cerrarse sola.. Por lo tanto, hicimos que el cuerpo trasero del portador tuviera una inclinación hacia atrás.. El ángulo está diseñado para que coincida con el ángulo de la capucha de la cola para que haya una sensación de unidad..
(Para el MT-25/03, retire la barra de agarre e instálela.. El YZF-R25/3 ha sido diseñado para reducir al mínimo la necesidad de hacer agujeros en el capó de la cola.. También se incluye un patrón para la fácil identificación de la ubicación de los agujeros..
Full set with base and screws required for installation.
In addition, the set comes with a limited edition rear box inner.
■The rear carrier for the same four models is available.
Yamaha's YZF-R25 and YZF-R3, MT-25 and MT-03 each share the same engine and frame.Although the vehicle configuration is slightly different, World Walk has developed a rear carrier that can be adjusted to fit four different models.
The YZF-R25 has a cowling and design reminiscent of supersports, while the MT-25 follows the image of a street-fighter.Both bikes have a slim, sharp image and are lightweight with powerful performance.
The rear rack is a practical part, but World Walk designed it not to destroy the sharp image as much as possible.
■Designed to be as sharp as possible while retaining space for the passenger.
In order to keep the sharp and tight image of the bike, the frame of the rear rack was brought up to the very edge of the seat.The design of the vehicle is as World Walk wanted, but it is too tight for the passenger to sit on.
The passenger seat was designed to be slightly wider than the first sample to allow room for a larger man to sit in the passenger seat.It is a tight fit without sacrificing passenger comfort.
■Maximum loading capacity is 5kg.World Walk is reinforcing every part of it.
Recently, it has become common to install a rear carrier and a rear box as a set, even for super sports inspired vehicles.Some of the larger rear boxes weigh about 5kg, so I reinforced each part of the box and set the maximum load capacity to 5kg.
The reinforcement plate is placed on the frame where the rear carrier is installed, and also on the legs of the main body.
■The shape of the buttocks is designed for practicality and design.
When the rear box is installed, the lid may close by itself if it is horizontal or raised forward when the lid is opened.This is why the rear rack is designed to be raised backwards.The angle of the tail cowl is the same as the angle of the tail cowl, so the design has a sense of unity.
To install, remove the grab bar from MT-25 / 03.YZF-R25 / 3 requires drilling of some parts of the tail cowl, but World Walk has designed the cowl so that drilling of the cowl is minimized.A paper pattern is also included to help you know where to drill the holes.