Una cerradura muy fuerte en forma de U con un fuerte cuerpo de acero y un fuerte barril de llave..
Se puede fijar a una llanta o rueda..
La barra de cierre está diseñada con un gran diámetro de 16 mm para un cierre más fuerte..
Gran ancho interno de la barra de bloqueo para usar con neumáticos más grandes..
Por supuesto, se puede usar tanto para bicicletas como para motos..
Cuando detecta la vibración, suena una fuerte alarma perforadora de 120dB para ayudar a evitar que le roben el coche..
El tratamiento especial de la superficie del cuerpo de la cerradura de disco, así como su impermeabilización, le dan un acabado lujoso..
La batería de la alarma es una batería de litio CR2. (Se puede usar durante unos 10 meses.)
Además, la alarma tiene una función de encendido y apagado..
------ Cómo operar ------
[Cómo encender/apagar]
Si gira la llave (aprox. 270 grados) para bloquear el dispositivo y luego la vuelve a girar, un solo "bip" sonará unos segundos después para indicar que la alarma de seguridad está en modo ON..
Al repetir la misma operación rápidamente después de encenderla, oirá un breve "bip" dos veces.. En este momento, la alarma de seguridad está apagada..
*Compruebe el sonido de la operación antes de cerrar la llave..
[Cómo instalar la batería]
*Necesitará un destornillador de cabeza Phillips además de las herramientas suministradas.. Por favor, prepárese..
1. Suelte la barra de bloqueo..
2. Inserte un destornillador de cabeza Phillips en el agujero de la barra de bloqueo y retire el tornillo..
*Retire el tornillo del lado sin el cilindro de la llave..
3. Retire la cubierta de silicona, la cubierta y la unidad de alarma, en ese orden.
4. Retire los dos tornillos de la unidad de alarma con la herramienta suministrada..
5. Retire la tapa de la batería y la cubierta impermeable e instale la batería..
6. ¡Reúnanse en orden inverso y listo!.
*Cuando instale la batería, por favor tenga cuidado de no olvidar la cubierta impermeable..
*Cuando instale la unidad de alarma, tenga cuidado de insertarla en la muesca..
This is a very strong U-shaped lock with a strong steel body and a strong key barrel.
It can be tightly fixed to tires and wheels.
The diameter of the lock bar is 16mm, which makes the lock stronger.
Also, the internal width of the lock bar is large enough to accommodate larger tires.
Of course, it can be used not only for motorcycles but also for bicycles.
When vibration is detected, a piercing alarm sounding at a loud volume of 120dB is emitted, and this product is effective in preventing theft of your vehicle.
In addition to waterproof specifications, the body of the disc lock is finished with a special surface treatment to give it a high-class look.
The battery for alarm is CR2 lithium battery.(It can be used for approx. 10 months)
In addition, the alarm has an [ON / OFF] function.
--- Operation ---
[How to switch ON / OFF]
When the key is turned (approx. 270°) to lock and then turned back, a short "beep" sound will be heard once, followed a few seconds later by a notification sound indicating that the security alarm has entered the ON mode.
By repeating the same operation quickly again after turning on the device, you will hear a short "beep" sound twice.In this case, the security alarm is turned off.
*When you lock the key, please confirm the sound of operation and lock the door.
[How to install the battery]
*A Phillips screwdriver is required in addition to the supplied tools.Please be prepared.
1. Remove the lock bar.
2. Insert a Phillips screwdriver into the hole of the lock bar and remove the screw.
*Remove the screw from the side without the key cylinder.
3. Remove the silicone cover, cover, and alarm unit in that order.
4. Remove the two screws from the alarm unit with the supplied tool.
5. Remove the battery cover and waterproof cover and install the battery.
6. Assemble in reverse order to complete.
*Please be careful not to forget to attach the waterproof cover when you install the battery.
*When installing the alarm unit, be careful to insert it into the notch on the alarm unit.